keyboard/qmk/lib/ugfx/boards/addons/gdisp/board_HX8347D_stm32f4discovery.h

164 lines
4.3 KiB
C

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.io/license.html
*/
/**
* @file boards/addons/gdisp/board_HX8347D_stm32f4discovery.h
* @brief GDISP Graphic Driver subsystem board SPI interface for the HX8347D display.
*
* @note This file contains a mix of hardware specific and operating system specific
* code. You will need to change it for your CPU and/or operating system.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
/* Pin assignments */
#define SET_RST palSetPad(GPIOB, 8)
#define CLR_RST palClearPad(GPIOB, 8)
#define SET_DATA palSetPad(GPIOB, 9)
#define CLR_DATA palClearPad(GPIOB, 9)
#define SET_CS palSetPad(GPIOA, 4)
#define CLR_CS palClearPad(GPIOA, 4)
/* PWM configuration structure. We use timer 4 channel 2 (orange LED on board). */
static const PWMConfig pwmcfg = {
1000000, /* 1 MHz PWM clock frequency. */
100, /* PWM period is 100 cycles. */
0,
{
{PWM_OUTPUT_ACTIVE_HIGH, 0},
{PWM_OUTPUT_ACTIVE_HIGH, 0},
{PWM_OUTPUT_ACTIVE_HIGH, 0},
{PWM_OUTPUT_ACTIVE_HIGH, 0}
},
0
};
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1cfg_8bit = {
0,
/* HW dependent part.*/
GPIOA,
4,
0 //SPI_CR1_BR_0
};
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 16bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1cfg_16bit = {
0,
/* HW dependent part.*/
GPIOA,
4,
SPI_CR1_DFF //SPI_CR1_BR_0
};
static GFXINLINE void init_board(GDisplay *g) {
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
/* Display backlight control */
/* TIM4 is an alternate function 2 (AF2) */
pwmStart(&PWMD4, &pwmcfg);
palSetPadMode(GPIOD, 13, PAL_MODE_ALTERNATE(2));
pwmEnableChannel(&PWMD4, 1, 100);
palSetPadMode(GPIOB, 8, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* RST */
palSetPadMode(GPIOB, 9, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* RS */
/*
* Initializes the SPI driver 1. The SPI1 signals are routed as follow:
* PB12 - NSS.
* PB13 - SCK.
* PB14 - MISO.
* PB15 - MOSI.
*/
SET_CS; SET_DATA;
spiStart(&SPID1, &spi1cfg_8bit);
palSetPadMode(GPIOA, 4, PAL_MODE_OUTPUT_PUSHPULL|PAL_STM32_OSPEED_HIGHEST); /* NSS. */
palSetPadMode(GPIOA, 5, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST); /* SCK. */
palSetPadMode(GPIOA, 6, PAL_MODE_ALTERNATE(5)); /* MISO. */
palSetPadMode(GPIOA, 7, PAL_MODE_ALTERNATE(5)|PAL_STM32_OSPEED_HIGHEST); /* MOSI. */
break;
}
}
static GFXINLINE void post_init_board(GDisplay *g) {
(void) g;
}
static GFXINLINE void setpin_reset(GDisplay *g, gBool state) {
(void) g;
if (state) {
CLR_RST;
} else {
SET_RST;
}
}
static GFXINLINE void set_backlight(GDisplay *g, gU8 percent) {
(void) g;
pwmEnableChannel(&PWMD4, 1, percent);
}
static GFXINLINE void acquire_bus(GDisplay *g) {
(void) g;
spiAcquireBus(&SPID1);
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0)); // Safety
CLR_CS;
}
static GFXINLINE void release_bus(GDisplay *g) {
(void) g;
SET_CS;
spiReleaseBus(&SPID1);
}
static GFXINLINE void busmode16(GDisplay *g) {
(void) g;
spiStart(&SPID1, &spi1cfg_16bit);
}
static GFXINLINE void busmode8(GDisplay *g) {
(void) g;
spiStart(&SPID1, &spi1cfg_8bit);
}
static GFXINLINE void write_index(GDisplay *g, gU8 index) {
(void) g;
CLR_DATA;
SPI1->DR = index;
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
SET_DATA;
}
static GFXINLINE void write_data(GDisplay *g, gU8 data) {
(void) g;
SPI1->DR = data;
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
}
static GFXINLINE void write_ram16(GDisplay *g, gU16 data) {
(void) g;
SPI1->DR = data;
while((SPI1->SR & SPI_SR_TXE) == 0);
}
#endif /* _GDISP_LLD_BOARD_H */