Remove base tidbit code as it's been merged to main zmk sources

keyboards/zmk-config/config/boards/shields/tidbit/Kconfig.defconfig

@@ -1,45 +0,0 @@
-# Copyright (c) 2020 The ZMK Contributors
-# SPDX-License-Identifier: MIT
-
-if SHIELD_TIDBIT
-
-config ZMK_KEYBOARD_NAME
-	default "tidbit"
-
-endif
-
-if ZMK_DISPLAY
-
-config I2C
-	default y
-
-config SSD1306
-	default y
-
-config SSD1306_REVERSE_MODE
-	default y
-
-endif # ZMK_DISPLAY
-
-if LVGL
-
-config LVGL_HOR_RES_MAX
-	default 128
-
-config LVGL_VER_RES_MAX
-	default 32
-
-config LVGL_VDB_SIZE
-	default 64
-
-config LVGL_DPI
-	default 148
-
-config LVGL_BITS_PER_PIXEL
-	default 1
-
-choice LVGL_COLOR_DEPTH
-	default LVGL_COLOR_DEPTH_1
-endchoice
-
-endif # LVGL

keyboards/zmk-config/config/boards/shields/tidbit/Kconfig.shield

@@ -1,5 +0,0 @@
-# Copyright (c) 2020 The ZMK Contributors
-# SPDX-License-Identifier: MIT
-
-config SHIELD_TIDBIT
-	def_bool $(shields_list_contains,tidbit)

keyboards/zmk-config/config/boards/shields/tidbit/README.md

@@ -1,50 +0,0 @@
-# Building ZMK for the Tidbit
-
-Some general notes/commands for building standard Tidbit layouts from the assembly documentation.
-
-## Standard "Non Dense" Build
-
-```
-
-west build -p --board nice_nano -d build/tidbit/default -- -DSHIELD=tidbit
-
-```
-
-## Dense "19 keys" Build
-
-```
-
-west build -p --board nice_nano -d build/tidbit/19_key -- -DSHIELD=tidbit_19key
-
-```
-
-## LED Notes
-
-If you built your tidbit without the LEDs *and* are using a Nice!Nano board, you'll need to add the following at the *end* of your local tidbit config.
-
-```
-
-CONFIG_ZMK_RGB_UNDERGLOW=n
-CONFIG_WS2812_STRIP=n
-
-```
-
-## Encoder Notes
-
-If you built your tidbit without encoders, you'll need to add the following at the *end* of your local tidbit config.
-
-```
-
-CONFIG_EC11=n
-CONFIG_EC11_TRIGGER_GLOBAL_THREAD=n
-
-```
-
-## OLED Builds
-
-If using an OLED screen you'll need to include the following at the *end* of your local tidbit config.
-
-```
-CONFIG_ZMK_DISPLAY=y
-
-```

keyboards/zmk-config/config/boards/shields/tidbit/boards/nice_nano.conf

@@ -1,4 +0,0 @@
-# Enable underglow
-CONFIG_ZMK_RGB_UNDERGLOW=y
-# Use the STRIP config specific to the LEDs you're using
-CONFIG_WS2812_STRIP=y

keyboards/zmk-config/config/boards/shields/tidbit/boards/nice_nano.overlay

@@ -1,34 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-&spi1 {
-  compatible = "nordic,nrf-spim";
-  status = "okay";
-  mosi-pin = <9>;
-  // Unused pins, needed for SPI definition, but not used by the ws2812 driver itself.
-  sck-pin = <5>;
-  miso-pin = <7>;
-
-  led_strip: ws2812@0 {
-    compatible = "worldsemi,ws2812-spi";
-    label = "WS2812";
-
-    /* SPI */
-    reg = <0>; /* ignored, but necessary for SPI bindings */
-    spi-max-frequency = <4000000>;
-
-    /* WS2812 */
-    chain-length = <8>; /* number of LEDs */
-    spi-one-frame = <0x70>;
-    spi-zero-frame = <0x40>;
-  };
-};
-
-/ {
-  chosen {
-		zmk,underglow = &led_strip;
-	};
-};

keyboards/zmk-config/config/boards/shields/tidbit/boards/proton_c.conf

@@ -1 +0,0 @@
-CONFIG_SENSOR=y

keyboards/zmk-config/config/boards/shields/tidbit/tidbit.conf

@@ -1,11 +0,0 @@
-# Copyright (c) 2020 The ZMK Contributors
-# SPDX-License-Identifier: MIT
-
-# Enable Encoders
-CONFIG_EC11=y
-CONFIG_EC11_TRIGGER_GLOBAL_THREAD=y
-
-# Enable underglow
-#CONFIG_ZMK_RGB_UNDERGLOW=y
-# Use the STRIP config specific to the LEDs you're using
-#CONFIG_WS2812_STRIP=y

keyboards/zmk-config/config/boards/shields/tidbit/tidbit.dtsi

@@ -1,116 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-#include <dt-bindings/zmk/matrix-transform.h>
-
-/ {
-	kscan0: kscan {
-		compatible = "zmk,kscan-gpio-matrix";
-		label = "KSCAN";
-
-		diode-direction = "row2col";
-
-		row-gpios
-			= <&pro_micro_d 15 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_d 7 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_d 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_d 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_d 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			;
-
-        col-gpios
-			= <&pro_micro_a 3 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_a 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_a 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			, <&pro_micro_a 0 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
-			;
-
-	};
-
-	default_transform: keymap_transform_0 {
-		compatible = "zmk,matrix-transform";
-		columns = <4>;
-		rows = <5>;
-
-		map = <
-                    RC(0,1) RC(0,2) RC(0,3)
-            RC(1,0) RC(1,1) RC(1,2) RC(1,3)
-            RC(2,0) RC(2,1) RC(2,2) RC(2,3)
-            RC(3,0) RC(3,1) RC(3,2) RC(3,3)
-            RC(4,0) RC(4,1) RC(4,2) RC(4,3)
-		>;
-	};
-
-	encoder_1_top_row: encoder_1_top_row {
-		compatible = "alps,ec11";
-		label = "Top Row Encoder";
-		a-gpios = <&pro_micro_d 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		b-gpios = <&pro_micro_d 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		resolution = <4>;
-		status = "disabled";
-	};
-
-	encoder_1: encoder_1 {
-		compatible = "alps,ec11";
-		label = "Encoder 1";
-		a-gpios = <&pro_micro_d 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		b-gpios = <&pro_micro_d 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		resolution = <4>;
-		status = "disabled";
-	};
-
-	encoder_2: encoder_2 {
-		compatible = "alps,ec11";
-		label = "Encoder 2";
-		a-gpios = <&pro_micro_d 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		b-gpios = <&pro_micro_d 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		resolution = <4>;
-		status = "disabled";
-	};
-
-	encoder_3: encoder_3 {
-		compatible = "alps,ec11";
-		label = "Encoder 3";
-		a-gpios = <&pro_micro_d 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		b-gpios = <&pro_micro_d 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		resolution = <4>;
-		status = "disabled";
-	};
-
-	encoder_4: encoder_4 {
-		compatible = "alps,ec11";
-		label = "Encoder 4";
-		a-gpios = <&pro_micro_d 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		b-gpios = <&pro_micro_d 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
-		resolution = <4>;
-		status = "disabled";
-	};
-
-    chosen {
-		zmk,kscan = &kscan0;
-		zmk,matrix_transform = &default_transform;
-	};
-};
-
-&pro_micro_i2c {
-	status = "disabled";
-
-	oled: ssd1306@3c {
-		compatible = "solomon,ssd1306fb";
-		reg = <0x3c>;
-		label = "DISPLAY";
-		width = <128>;
-		height = <32>;
-		segment-offset = <0>;
-		page-offset = <0>;
-		display-offset = <0>;
-		multiplex-ratio = <31>;
-		segment-remap;
-		com-invdir;
-		com-sequential;
-		prechargep = <0x22>;
-	};
-};

keyboards/zmk-config/config/boards/shields/tidbit/tidbit.keymap

@@ -1,53 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-#include <behaviors.dtsi>
-#include <dt-bindings/zmk/bt.h>
-#include <dt-bindings/zmk/outputs.h>
-#include <dt-bindings/zmk/keys.h>
-
-&encoder_1_top_row {
-    status = "okay";
-};
-
-&pro_micro_i2c {
-	status = "okay";
-};
-
-/ {
-    sensors {
-		compatible = "zmk,keymap-sensors";
-		sensors = <&encoder_1_top_row>;
-	};
-
-    keymap {
-        compatible = "zmk,keymap";
-        
-        default_layer {
-            bindings = <
-                                &kp KP_NUMLOCK  &kp KP_ASTERISK &kp KP_MINUS
-                &kp KP_NUMBER_7 &kp KP_NUMBER_8 &kp KP_NUMBER_9 &kp KP_PLUS
-                &kp KP_NUMBER_4 &kp KP_NUMBER_5 &kp KP_NUMBER_6 &kp &none
-                &kp KP_NUMBER_1 &kp KP_NUMBER_2 &kp KP_NUMBER_3 &lt 1 KP_ENTER
-                &none           &kp KP_NUMBER_0 &kp KP_DOT      &none
-            >;
-
-            sensor-bindings = <&inc_dec_kp C_VOLUME_UP C_VOLUME_DOWN>;
-        };
-
-         func_layer {
-             bindings = <
-                                &none           &reset          &bootloader
-                &out OUT_TOG    &out OUT_USB    &out OUT_BLE    &none
-                &bt BT_SEL 0    &bt BT_PRV      &bt BT_NXT      &bt BT_CLR
-                &bt BT_SEL 1    &bt BT_SEL 2    &bt BT_SEL 3    &tog 0
-                &kp C_MUTE      &none           &none           &none
-             >;
-
-             sensor-bindings = <&inc_dec_kp C_VOLUME_UP C_VOLUME_DOWN>;
-         };
-    };
-};

keyboards/zmk-config/config/boards/shields/tidbit/tidbit.overlay

@@ -1,7 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-#include "tidbit.dtsi"

keyboards/zmk-config/config/boards/shields/tidbit/tidbit_19key.conf

@@ -1,11 +0,0 @@
-# Copyright (c) 2020 The ZMK Contributors
-# SPDX-License-Identifier: MIT
-
-# Enable Encoders
-CONFIG_EC11=y
-CONFIG_EC11_TRIGGER_GLOBAL_THREAD=y
-
-# Enable underglow
-#CONFIG_ZMK_RGB_UNDERGLOW=y
-# Use the STRIP config specific to the LEDs you're using
-#CONFIG_WS2812_STRIP=y

keyboards/zmk-config/config/boards/shields/tidbit/tidbit_19key.keymap

@@ -1,54 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-#include "tidbit.dtsi"
-#include <behaviors.dtsi>
-#include <dt-bindings/zmk/keys.h>
-#include <dt-bindings/zmk/bt.h>
-#include <dt-bindings/zmk/outputs.h>
-
-&encoder_4 {
-    status = "okay";
-};
-
-&pro_micro_i2c {
-	status = "okay";
-};
-
-/ {
-    sensors {
-		compatible = "zmk,keymap-sensors";
-		sensors = <&encoder_4>;
-	};
-
-    keymap {
-        compatible = "zmk,keymap";
-        
-        default_layer {
-            bindings = <
-                                &tog 1          &kp KP_NUMLOCK  &kp KP_SLASH
-                &kp KP_NUMBER_7 &kp KP_NUMBER_8 &kp KP_NUMBER_9 &kp KP_ASTERISK
-                &kp KP_NUMBER_4 &kp KP_NUMBER_5 &kp KP_NUMBER_6 &kp KP_MINUS
-                &kp KP_NUMBER_1 &kp KP_NUMBER_2 &kp KP_NUMBER_3 &kp KP_PLUS
-                &kp C_MUTE      &kp KP_NUMBER_0 &kp KP_DOT      &kp KP_ENTER
-            >;
-
-            sensor-bindings = <&inc_dec_kp C_VOLUME_UP C_VOLUME_DOWN>;
-        };
-
-         func_layer {
-             bindings = <
-                                &tog 0          &reset          &bootloader
-                &out OUT_TOG    &out OUT_USB    &out OUT_BLE    &none
-                &bt BT_SEL 0    &bt BT_PRV      &bt BT_NXT      &bt BT_CLR
-                &bt BT_SEL 1    &bt BT_SEL 2    &bt BT_SEL 3    &none
-                &kp C_MUTE      &none           &none           &none
-             >;
-
-            sensor-bindings = <&inc_dec_kp C_VOLUME_UP C_VOLUME_DOWN>;
-         };
-    };
-};

keyboards/zmk-config/config/boards/shields/tidbit/tidbit_19key.overlay

@@ -1,8 +0,0 @@
-/*
- * Copyright (c) 2020 The ZMK Contributors
- *
- * SPDX-License-Identifier: MIT
- */
-
-#include "tidbit.dtsi"
-#include "tidbit_19key.keymap"

keyboards/zmk-config/notes.md

@@ -36,6 +36,10 @@
 - Push and hold button to clear BT profile
 - Tap button to connect to default BT profile
 
+# Generating settings reset images
+
+west build --board nice_nano -d build/settings_reset -- -DSHIELD=settings_reset
+
 # VS Code Documentation
 
 - Command Pallet -> Run Task -> npm -> Shows list of npm build tasks for the docs