keyboard/qmk/lib/vusb/examples/hid-custom-rq/firmware/main.c

121 lines
4.9 KiB
C
Raw Normal View History

/* Name: main.c
* Project: hid-custom-rq example
* Author: Christian Starkjohann
* Creation Date: 2008-04-07
* Tabsize: 4
* Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
*/
/*
This example should run on most AVRs with only little changes. No special
hardware resources except INT0 are used. You may have to change usbconfig.h for
different I/O pins for USB. Please note that USB D+ must be the INT0 pin, or
at least be connected to INT0 as well.
We assume that an LED is connected to port B bit 0. If you connect it to a
different port or bit, change the macros below:
*/
#define LED_PORT_DDR DDRB
#define LED_PORT_OUTPUT PORTB
#define LED_BIT 0
#include <avr/io.h>
#include <avr/wdt.h>
#include <avr/interrupt.h> /* for sei() */
#include <util/delay.h> /* for _delay_ms() */
#include <avr/pgmspace.h> /* required by usbdrv.h */
#include "usbdrv.h"
#include "oddebug.h" /* This is also an example for using debug macros */
#include "requests.h" /* The custom request numbers we use */
/* ------------------------------------------------------------------------- */
/* ----------------------------- USB interface ----------------------------- */
/* ------------------------------------------------------------------------- */
PROGMEM const char usbHidReportDescriptor[22] = { /* USB report descriptor */
0x06, 0x00, 0xff, // USAGE_PAGE (Generic Desktop)
0x09, 0x01, // USAGE (Vendor Usage 1)
0xa1, 0x01, // COLLECTION (Application)
0x15, 0x00, // LOGICAL_MINIMUM (0)
0x26, 0xff, 0x00, // LOGICAL_MAXIMUM (255)
0x75, 0x08, // REPORT_SIZE (8)
0x95, 0x01, // REPORT_COUNT (1)
0x09, 0x00, // USAGE (Undefined)
0xb2, 0x02, 0x01, // FEATURE (Data,Var,Abs,Buf)
0xc0 // END_COLLECTION
};
/* The descriptor above is a dummy only, it silences the drivers. The report
* it describes consists of one byte of undefined data.
* We don't transfer our data through HID reports, we use custom requests
* instead.
*/
/* ------------------------------------------------------------------------- */
usbMsgLen_t usbFunctionSetup(uchar data[8])
{
usbRequest_t *rq = (void *)data;
if((rq->bmRequestType & USBRQ_TYPE_MASK) == USBRQ_TYPE_VENDOR){
DBG1(0x50, &rq->bRequest, 1); /* debug output: print our request */
if(rq->bRequest == CUSTOM_RQ_SET_STATUS){
if(rq->wValue.bytes[0] & 1){ /* set LED */
LED_PORT_OUTPUT |= _BV(LED_BIT);
}else{ /* clear LED */
LED_PORT_OUTPUT &= ~_BV(LED_BIT);
}
}else if(rq->bRequest == CUSTOM_RQ_GET_STATUS){
static uchar dataBuffer[1]; /* buffer must stay valid when usbFunctionSetup returns */
dataBuffer[0] = ((LED_PORT_OUTPUT & _BV(LED_BIT)) != 0);
usbMsgPtr = dataBuffer; /* tell the driver which data to return */
return 1; /* tell the driver to send 1 byte */
}
}else{
/* calss requests USBRQ_HID_GET_REPORT and USBRQ_HID_SET_REPORT are
* not implemented since we never call them. The operating system
* won't call them either because our descriptor defines no meaning.
*/
}
return 0; /* default for not implemented requests: return no data back to host */
}
/* ------------------------------------------------------------------------- */
int __attribute__((noreturn)) main(void)
{
uchar i;
wdt_enable(WDTO_1S);
/* If you don't use the watchdog, replace the call above with a wdt_disable().
* On newer devices, the status of the watchdog (on/off, period) is PRESERVED
* OVER RESET!
*/
/* RESET status: all port bits are inputs without pull-up.
* That's the way we need D+ and D-. Therefore we don't need any
* additional hardware initialization.
*/
odDebugInit();
DBG1(0x00, 0, 0); /* debug output: main starts */
usbInit();
usbDeviceDisconnect(); /* enforce re-enumeration, do this while interrupts are disabled! */
i = 0;
while(--i){ /* fake USB disconnect for > 250 ms */
wdt_reset();
_delay_ms(1);
}
usbDeviceConnect();
LED_PORT_DDR |= _BV(LED_BIT); /* make the LED bit an output */
sei();
DBG1(0x01, 0, 0); /* debug output: main loop starts */
for(;;){ /* main event loop */
#if 0 /* this is a bit too aggressive for a debug output */
DBG2(0x02, 0, 0); /* debug output: main loop iterates */
#endif
wdt_reset();
usbPoll();
}
}
/* ------------------------------------------------------------------------- */