keyboard/qmk/lib/ugfx/boards/addons/gdisp/board_SSD1289_stm32f4discovery.h

181 lines
5.9 KiB
C
Raw Normal View History

/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.io/license.html
*/
/**
* @file boards/addons/gdisp/board_SSD1289_stm32f4discovery.h
* @brief GDISP Graphic Driver subsystem board interface for the SSD1289 display.
*
* @note This file contains a mix of hardware specific and operating system specific
* code. You will need to change it for your CPU and/or operating system.
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
// For a multiple display configuration we would put all this in a structure and then
// set g->board to that structure.
#define GDISP_REG ((volatile gU16 *) 0x60000000)[0] /* RS = 0 */
#define GDISP_RAM ((volatile gU16 *) 0x60020000)[0] /* RS = 1 */
#define GDISP_DMA_STREAM STM32_DMA2_STREAM6
#define FSMC_BANK 0
/* PWM configuration structure. We use timer 3 channel 3 */
static const PWMConfig pwmcfg = {
100000, /* 100 kHz PWM clock frequency. */
100, /* PWM period is 100 cycles. */
0,
{
{PWM_OUTPUT_DISABLED, 0},
{PWM_OUTPUT_DISABLED, 0},
{PWM_OUTPUT_ACTIVE_HIGH, 0},
{PWM_OUTPUT_DISABLED, 0}
},
0,
0
};
static GFXINLINE void init_board(GDisplay *g) {
// As we are not using multiple displays we set g->board to NULL as we don't use it.
g->board = 0;
switch(g->controllerdisplay) {
case 0: // Set up for Display 0
/**
* Performs the following functions:
* 1. initialise the io port used by the display
* 2. initialise the reset pin (initial state not-in-reset)
* 3. initialise the chip select pin (initial state not-active)
* 4. initialise the backlight pin (initial state back-light off)
*/
#if defined(STM32F1XX) || defined(STM32F3XX)
/* FSMC setup for F1/F3 */
rccEnableAHB(RCC_AHBENR_FSMCEN, 0);
#if defined(GDISP_USE_DMA)
#error "GDISP: SSD1289 - DMA not implemented for F1/F3 Devices"
#endif
#elif defined(STM32F4XX) || defined(STM32F2XX)
/* STM32F2-F4 FSMC init */
rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
#if defined(GDISP_USE_DMA)
if (dmaStreamAllocate(GDISP_DMA_STREAM, 0, 0, 0)) gfxExit();
dmaStreamSetMemory0(GDISP_DMA_STREAM, &GDISP_RAM);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
#else
#if GFX_COMPILER_WARNING_TYPE == GFX_COMPILER_WARNING_DIRECT
#warning "GDISP: SSD1289 - DMA is supported for F2/F4 Devices. Define GDISP_USE_DMA in your gfxconf.h to turn this on for better performance."
#elif GFX_COMPILER_WARNING_TYPE == GFX_COMPILER_WARNING_MACRO
COMPILER_WARNING("GDISP: SSD1289 - DMA is supported for F2/F4 Devices. Define GDISP_USE_DMA in your gfxconf.h to turn this on for better performance.")
#endif
#endif
#else
#error "GDISP: SSD1289 - FSMC not implemented for this device"
#endif
/* set pins to FSMC mode */
IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 7) | (1 << 8) |
(1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0};
IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
(1 << 13) | (1 << 14) | (1 << 15), 0};
palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
/* FSMC timing */
FSMC_Bank1->BTCR[FSMC_BANK+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
/* Bank1 NOR/SRAM control register configuration
* This is actually not needed as already set by default after reset */
FSMC_Bank1->BTCR[FSMC_BANK] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
/* Display backlight control */
/* TIM3 is an alternate function 2 (AF2) */
pwmStart(&PWMD3, &pwmcfg);
palSetPadMode(GPIOB, 0, PAL_MODE_ALTERNATE(2));
pwmEnableChannel(&PWMD3, 2, 100);
break;
}
}
static GFXINLINE void post_init_board(GDisplay *g) {
(void) g;
}
static GFXINLINE void setpin_reset(GDisplay *g, gBool state) {
(void) g;
(void) state;
}
static GFXINLINE void set_backlight(GDisplay *g, gU8 percent) {
(void) g;
pwmEnableChannel(&PWMD3, 2, percent);
}
static GFXINLINE void acquire_bus(GDisplay *g) {
(void) g;
}
static GFXINLINE void release_bus(GDisplay *g) {
(void) g;
}
static GFXINLINE void write_index(GDisplay *g, gU16 index) {
(void) g;
GDISP_REG = index;
}
static GFXINLINE void write_data(GDisplay *g, gU16 data) {
(void) g;
GDISP_RAM = data;
}
static GFXINLINE void setreadmode(GDisplay *g) {
(void) g;
FSMC_Bank1->BTCR[FSMC_BANK+1] = FSMC_BTR1_ADDSET_3 | FSMC_BTR1_DATAST_3 | FSMC_BTR1_BUSTURN_0; /* FSMC timing */
}
static GFXINLINE void setwritemode(GDisplay *g) {
(void) g;
FSMC_Bank1->BTCR[FSMC_BANK+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0; /* FSMC timing */
}
static GFXINLINE gU16 read_data(GDisplay *g) {
(void) g;
return GDISP_RAM;
}
#if defined(GDISP_USE_DMA) || defined(__DOXYGEN__)
static GFXINLINE void dma_with_noinc(GDisplay *g, gColor *buffer, int area) {
(void) g;
dmaStreamSetPeripheral(GDISP_DMA_STREAM, buffer);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
for (; area > 0; area -= 65535) {
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area > 65535 ? 65535 : area);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
}
}
static GFXINLINE void dma_with_inc(GDisplay *g, gColor *buffer, int area) {
(void) g;
dmaStreamSetPeripheral(GDISP_DMA_STREAM, buffer);
dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PINC | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
for (; area > 0; area -= 65535) {
dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area > 65535 ? 65535 : area);
dmaStreamEnable(GDISP_DMA_STREAM);
dmaWaitCompletion(GDISP_DMA_STREAM);
}
}
#endif
#endif /* _GDISP_LLD_BOARD_H */